There are many well-liked woodworking joints. A Woodworking joint's strength varies, and a few could be far better than others.  Which of them are ideal for your hard work

At the receiving end Joint joins two pieces of wood merely by butting them together. At the receiving end joint could be the simplest to produce. It does not take weakest joint, and you also must use some kind of reinforcement. You have an end grain to long grain gluing surface. The resulting joint is of course weak. It relies on glue to hold it together; however, glue won't have much lateral strength. You are able to break this joint together with your bare hands.

A biscuit joint is nothing greater than a reinforced Butt joint. The biscuit is an oval-shaped piece and is also made from dried and compressed wood, such as beech. You install it in matching mortises both in bits of the joint. Most people work with a biscuit joiner to make the mortises. You design the biscuit joint to permit flexibility in glue-up. However, you should locate the mortise the proper distance through the face in the joint in the pieces. Since the biscuit is thin, you'll be able to move the alignment around. Here is the very reason that I don't such as this joint. It's not at all in perfect alignment. Additionally, you waste your dollars around the Biscuit Joiner and plenty of time cutting the mortises in each bit of stock. Why bother

 A bridle joint is just like a mortise and tenon. You cut a tenon about the end of one piece along with a full width mortise within the other piece to just accept it. This can be a distinguishing feature of this joint You've got only three gluing surfaces.

The corner bridle joint joins two pieces at their ends, forming a corner. You employ this joint to deal with a rail in uprights, including legs. It provides good strength in compression and it is fairly proof against racking. You have to work with a mechanical fastener or pin.

 A dado may be a slot cut in to the surface of your piece of wood. When viewed in cross-section, a dado has three sides. You cut a dado perpendicular for the grain. It's completely different from a groove, that you just cut parallel for the grain. A through dado passes right through the top as well as ends are open. A stopped dado has either within the ends stop before meeting the edge with the surface. You use dadoes to connect shelves to some bookcase carcass. You rabbet the shelves to fit the dado, that makes the rabbet and dado joint.

The dovetail joint, or simply dovetail, is a strong woodworking joint, and is also perfect for tensile strength (resistance from pulling apart). The dovetail joint can be used to connect the sides of the drawer to the front. A number of pins cut to extend through the end of just one board interlock which has a series of tails cut to the end of one other board. The pins and tails have a very trapezoidal shape. Once glued, the joint is permanent, and requirements no mechanical fasteners. A lot of people use a dovetailed dado, because of the tensile strength.

 A finger joint or box joint is employed to participate two pieces of wood at right angles to each other. It really is much like a dovetail joint apart from the pins are square and not angled. The joint relies on glue to support together. No have the mechanical strength of the dovetail.

 A half lap joint is done by removing material from every bit so your resulting joint could be the thickness from the thickest piece. Generally, the pieces are of the thickness. You remove half the thickness of each and every. This joint is useful for making workshop storage items.

Among the strongest woodworking joints may be the mortise and tenon joint. This joint is straightforward and strong. Woodworkers manipulate it for a number of years. Normally you have it to participate two pieces of wood at 90-degrees. A mortise is really a cavity cut right into a piece of wood to obtain a tenon. A tenon is really a projection around the end of a piece of wood to insert into a mortise. You insert one end of a piece right into a hole in the other piece. A quality mortise and tenon joint gives perfect registration of the two pieces. This will be significant when building heirloom pieces.

The Pocket-Hole Joint is certainly not greater Butt joint with Pocket Hole Screws. The pocket holes require two drilling operations. The foremost is to counterbore the pocket hole itself, that can take the screw head. The next step would be to drill an airplane pilot hole whose centerline is the same as the pocket hole. Most people utilize a pocket-hole jig, like the Kreg Jig(TM). This jig enables you to drill pocket holes on the correct angle also to the proper depth. Glue should be utilized to strengthen the joint. Naturally, the Kreg Jig(TM) costs from $40 as much as $140. To me, that is a fortune whenever you are able increase the risk for mortise & tenon jigs to get a fraction of this price. Moreover, the mortise and tenon joint is much stronger.

 A rabbet is often a recess cut in to the edge of wood. When viewed in cross-section, a rabbet is two-sided and ready to accept the conclusion of the surface. An illustration of this using a rabbet is within the back fringe of a cabinet. The rabbet allows a corner to match flush using the sides. Another example will be the insertion of a glass pane using a rabbet around the fringe of the frame.

Tongue and groove is manufactured by cutting a slot (groove) along one edge. The opposite piece includes a tongue cut about the mating edge. Consequently, a couple of pieces fit together closely. You can use it to produce wide tabletops from solid wood. Various other uses will be in timber flooring, parquetry, paneling, etc.

For additional info on Woodworking Joints, including pictures along with the video by WOOD Magazine showing the final results of these tests, go to http://www.provenwoodworking.com/woodworking-joints.html

Copyright 2009 - Jim McCleary of provenwoodworking. woodworking plans com. All Rights Reserved Worldwide. Reprint Rights: You could possibly reprint this information if you leave every one of the links active, do not edit the article in any way, and present author name credit.